IIMS News

Cley Harbour rejuvenated after many years of disuse

Posted on by News Hound
Photo credit: Chris Taylor
Photo credit: Chris Taylor

Norfolk’s Cley Harbour has received its largest traditional working sailing vessel for more than 60 years, marking its return to activity after falling into disuse.

The Coastal Exploration Company owned 30ft open wooden gaff rigged whelk boat Salford came into the harbour to deliver a cargo of North Norfolk beer from Barsham Brewery to the Cley Windmill.

Simon Read, chairman of Cley Harbour committee said: “This is the largest traditional working sailing vessel to visit Cley in over 60 years and will be mark a key moment in the rejuvenation of Cley Harbour.”

The clinker-built traditional Norfolk fishing boat has remained in and around Norfolk’s waters since it was built in the 1950s and was recently in the filming of Continue reading “Cley Harbour rejuvenated after many years of disuse”

IMO has adopted a plan to address the issue of marine plastic rubbish

Posted on by News Hound
Dumping plastics into the sea is already prohibited under MARPOL regulations, which also oblige governments to ensure adequate port reception facilities to receive ship waste.
Dumping plastics into the sea is already prohibited under MARPOL regulations, which also oblige governments to ensure adequate port reception facilities to receive ship waste.

The IMO has pledged to address the significant problem posed by plastics to the marine environment, with the adoption of an action plan which aims to enhance existing regulations and introduce new supporting measures to reduce marine plastic litter from ships.

The plan was adopted on October 26 by IMO’s Marine Environment Protection Committee (MEPC).

Dumping plastics into the sea is already prohibited under MARPOL regulations, which also oblige governments to ensure adequate port reception facilities to receive ship waste. Under the London Convention and Protocol on the dumping of wastes at sea, only permitted materials can be dumped and this waste – such as from dredging – has to be fully assessed to ensure it does not contain harmful materials like plastics.

However, studies demonstrate that despite the existing regulatory framework to prevent marine plastic litter from ships, discharges into the sea continue to occur. Recognising that more Continue reading “IMO has adopted a plan to address the issue of marine plastic rubbish”

Workboat apprenticeship scheme tackles skills and crewing challenges

Posted on by News Hound
Training providers including 54 North Maritime and Red Ensign are drawing up plans to run courses for the scheme
Training providers including 54 North Maritime and Red Ensign are drawing up plans to run courses for the scheme

The National Workboat Association (NWA) has finalised its Workboat Crewmember Apprenticeship standard as the industry faces growing skills and crewing challenges in the thriving workboat sector.

This scheme is aimed at addressing industry concerns about falling numbers of young people entering the industry at ground level, exasperated by experienced seafarers leaving the industry, often by retirement.

As well as tugs and ‘multicat’-type vessels the definition of workboat in this context includes: offshore wind personnel transfer vessels, survey craft and pilot vessels, all sectors experiencing growth involving increasingly sophisticated and technically demanding vessels but still requiring seamanship skills that have been around for generations. The new apprenticeship standard has now been finalised, paving the way for the scheme to be rolled out by training providers across England and Wales.

The Workboat Crewmember Standard and assessment has been Continue reading “Workboat apprenticeship scheme tackles skills and crewing challenges”

New dry dock initiative uses inflatable buoyancy

Posted on by News Hound
For the next phase of construction; the installation of the upper decks to take place, the dry dock needed to be flooded and the hull then towed to the wet dock.
For the next phase of construction; the installation of the upper decks to take place, the dry dock needed to be flooded and the hull then towed to the wet dock.

Unique Group’s Buoyancy & Ballast division has recently facilitated a high-profile dry dock project in Romania, involving the supply and operation of 840t of Seaflex inflatable buoyancy.

The hull and lower decks of the Australian Antarctic Division’s (AAD) new icebreaker Nuyina were constructed in the dry dock at Damen’s Galati Shipyard.

“Our Buoyancy & Ballast division is truly unique within the market and we consistently bring added value to our clients, working in partnership,” said Chris Sparrow, global sales manager, Buoyancy & Ballast at Unique Group.

“We get right up to speed early on in a project during Continue reading “New dry dock initiative uses inflatable buoyancy”

Preventing coal cargo from self-heating

Posted on by News Hound
The atmosphere in each cargo hold should be monitored, at least on a daily basis, for CO, hydrogen sulphide (H2 S), oxygen (O2) and flammable gas (LEL-methane).
The atmosphere in each cargo hold should be monitored, at least on a daily basis, for CO, hydrogen sulphide (H2 S), oxygen (O2) and flammable gas (LEL-methane).

London P&I Club has analysed the problems associated with the transportation of coal in bulk, such as self-heating and flammable gas (i.e. methane) release. Self-heating can lead to fires and the production of carbon monoxide (CO), whilst methane release can lead to an explosive atmosphere being generated in the hold.

Self-heating normally occurs in localised hot spots within a bulk cargo, and temperature measurements are unlikely to identify problems. However, when coal self-heats it produces CO, so measuring the concentration of CO is the most effective method to identify a self-heating cargo.

The atmosphere in each cargo hold should be monitored, at least on a daily basis, for CO, hydrogen sulphide (H2 S), oxygen (O2) and flammable gas (LEL-methane). If the holds are being ventilated, then ventilation should be stopped at least Continue reading “Preventing coal cargo from self-heating”

How to conduct a safe bunkering operation

Posted on by News Hound
A number of safe bunkering measures are required for each bunkering operation. These can be divided into four stages and checks
A number of safe bunkering measures are required for each bunkering operation. These can be divided into four stages and checks

The UK P&I Club has published helpful guidance to ensure safe bunkering operations. The Club said that bunkering operations are routine and critical, high risk operations which require to be carefully planned and performed.

Causes of bunker spills
Although the most of the bunker transfers are carried out without incident, very occasionally, things can and do go wrong. The UK Club notes that only a minority of cases do bunker spills occur because of failure of the hoses or pipelines, while the majority of spills result from a tank overflowing.

But these are not the only causes. Common causes of bunker spills can be summarised as follows:

– Improper set up of pipeline system valves: Potentially causing either overpressure, or flow of bunkers to an unintended location;
– Insufficient monitoring of tank levels during bunkering: All tanks, not only those Continue reading “How to conduct a safe bunkering operation”

Loss of propulsion leads dredger to collide with loaded barge says report

Posted on by News Hound
The FRPD 309 sustained damage to the shell plating and forepeak tank forward of the collision bulkhead. In addition, the port anchor was disconnected from its housing and became wedged in the Evco 60's hull
The FRPD 309 sustained damage to the shell plating and forepeak tank forward of the collision bulkhead. In addition, the port anchor was disconnected from its housing and became wedged in the Evco 60’s hull

The Transportation Safety Board of Canada released its investigation report into the collision of the dredger FRPD 309 with the loaded barge Evco 60, on 5 December 2017, in the Fraser River.

The incident
On 04 December 2017, the dredger FRPD 309 departed a shipyard in Delta, BC, to begin dredging in the Fraser River. The vessel is a conventional trailing arm suction dredger, with the bridge and accommodation located forward and machinery space located aft. Before departure, the crew had carried out pre-departure checks, a safety meeting, and emergency drills.

After arriving at the dredging location, the vessel started dredging sand and sediment from the river bed into the hopper using the 2 trailing arms and a dredging pump. When the hopper was filled, the sand and sediment was pumped ashore via a pipeline. The master left the bridge, handing over the command of the vessel to the officer of the watch (OOW). Two engineers, 2 deckhands, and a pipe operator were also on duty.

As the vessel was turning and the pipe operator was raising the trailing arms to the deck level, the vessel experienced Continue reading “Loss of propulsion leads dredger to collide with loaded barge says report”

Bavaria Yachts is relying on 100 percent Made in Giebelstadt for future success

Posted on by News Hound

The future development of Bavaria is taking clear shape: The yacht builder, respected worldwide for its good price/performance ratio, will once again build its boats one hundred percent in Germany. Bearing the seal of quality “Made in Giebelstadt”, both sailing and motor yachts will be manufactured and handed over to customers in Franconia. The R55 motor yacht, previously produced in Croatia, will for the first time be hand-built at the company’s headquarters in the first half of 2019. The moulds and tools are currently being transported from Croatia to Germany and installed in Giebelstadt.

“We want our outstandingly well trained and committed employees to develop and build all our yachts primarily under own management. The workforce identifies strongly with Bavaria Yachts; it is the key feature of our company,” explains Managing Director Erik Appel, who has been Chief Operating Officer of Bavaria Yachts since December 2017. “This is why we intend to further increase our permanent staff and simultaneously reduce the proportion of temporary workers. This will help considerably to bring down Continue reading “Bavaria Yachts is relying on 100 percent Made in Giebelstadt for future success”

MAIB issues safety warning about enclose space work after FV Sunbeam

Posted on by News Hound

This urgent bulletin has been issued after working in a refrigerated saltwater tank resulted in a fatal accident on board fv Sunbeam (FR487) at Fraserburgh, Scotland.

Initial findings
At about 0900 on 14 August, FV Sunbeam crew arrived at the vessel’s berth ready to begin work. The vessel’s refrigeration plant had been shut down after landing the final catch at Lerwick, and its RSW tanks had been pumped out and tank lids opened in preparation for deep cleaning. At some time between 1200 and 1350, Sunbeam’s second engineer entered the aft centre RSW tank and collapsed.

Continue reading “MAIB issues safety warning about enclose space work after FV Sunbeam”

Prepare and make way for the world’s largest ship, the Havfarm

Posted on by News Hound
On the drawing board is a ship known as Havfarm (“Ocean Farm”), 430 metres in length and 54 metres wide, it will lay at anchor, fixed to the seafloor using the offshore industry’s technological solutions.
On the drawing board is a ship known as Havfarm (“Ocean Farm”), 430 metres in length and 54 metres wide, it will lay at anchor, fixed to the seafloor using the offshore industry’s technological solutions.

In conjunction with Nordlaks, NSK Ship Design has designed an aquaculture ship that could be the beginning of a sustainable revolution in the fish farming industry, named the Havfarm.

There is an air of excitement at NSK Ship Design, because they have been quietly working away since June 2015 on a special project for Nordlaks – a project that can be classified as no less than sensational for the fish farming industry.

On the drawing board is a ship known as Havfarm (“Ocean Farm”), 430 metres in length and 54 metres wide, it will lay at anchor, fixed to the seafloor using the offshore industry’s technological solutions. Norway is a world leader in Continue reading “Prepare and make way for the world’s largest ship, the Havfarm”

Complaints received by the Canal & River Trust are on the up

Posted on by News Hound
Of the other complaints, there was one about the routing of HS2, as well as others in some way related to land or property.
Of the other complaints, there was one about the routing of HS2, as well as others in some way related to land or property.

252 complaints were received by the Canal & River Trust in 2017/18, according to the latest Waterways Ombudsman report.

The report show that the number of complaints is above the average of 225 over the past five years. During the year the Ombudsman received 35 enquiries about the Trust, down on 39 last year. Fifteen new investigations were opened, which was one more than the previous year and the number of completed investigations was 14, three lower than the previous year.

Of the 14 investigations completed, one was upheld, while in a further four investigations the complaint was either upheld in part, or elements of it were upheld. Goodwill awards were proposed in three cases, although in one case the complainant did not accept it.

Wide-ranging complaints
There was a very diverse range of complaints. The majority were about Continue reading “Complaints received by the Canal & River Trust are on the up”

Sunseeker is set to move into metal boat production

Posted on by News Hound
The new 49m tri-deck yacht will have an interior that can be styled to each owner’s taste.
The new 49m tri-deck yacht will have an interior that can be styled to each owner’s taste.

Sunseeker International is set to partner with Dutch based ICON Yachts to produce aluminium boats.

The first boat, due for launch in 2021, will be a 49m yacht and will capitalise on the demand the boatbuilder is seeing for larger vessels.

“We know there is demand there for larger Sunseeker yachts as the 155 Yacht proved,” said Sunseeker International sales director, Sean Robertson. “The decision to stop building that model was a commercial one based on space and capacity and certainly not due to lack of demand, so we knew we needed to rethink our approach to this size of vessel and have spent considerable time looking at various opportunities.”

He added: “A move into metal also means there is no Continue reading “Sunseeker is set to move into metal boat production”

Instagram Posts from the IIMS @iimsmarine

Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.

Strictly Necessary Cookies

Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings.

Show details
Performance & Marketing Cookies

This website uses Google Analytics to collect anonymous information such as the number of visitors to the site, and the most popular pages. This also helps us optimise our marketing campaigns. User data sent to Google Analytics may be used for ad personalization and measurement of our ad campaigns. Keeping this cookie enabled helps us to improve our website.

Show details
Powered by  GDPR Cookie Compliance